• Wood Grips For Colt Detective Special
• Wood Grips For Colt Detective Special
• Custom Grips For Colt Detective Special

I have a Det Special from the late 1980's with the factory grips that cover the front strap, no medalian. I'd like to have a set of the vintage grips with the Colt Medalian on them.It seems I cannot find matched sets. The two grip panels come from two separate sets and do not match. I have called people who have them listed and they are very up front and advise me that they are not a matched set.Does anyone know where these might be found for a reasonable price?Also, does anyone have a photo of the Ajax Ivory Polymer grips for the Detective Special?Thanks. The reason you can't find matched Colt grips, is because Colt didn't make matched grips.Even most of the Colt Custom Shop fancy grips aren't matched.To find Colt Detective Special grips with Gold or Silver medallions check Gun Parts Corporation atAnd Ebay. Colt DS grips show up there fairly often, and usually sell for reasonable prices.The correct grips for your era Colt will be the vintage 'Service' type grips which overlap on the bottom of the butt.Earlier Detective Specials had a longer steel butt.The correct overlap grips are shown here.

The Colt D-Frame grips by ALTAMONT® come in a Classic Panel and an. To the Detective Special, Commando Special, Cobra, Agent, Diamondback, Police.

A Colt Detective Special, Fourth Series, with barrel shroud enclosing and protecting the ejector-rod and rubber gripsTypePlace of originUnited StatesProduction historyManufacturerProduced193–1995VariantsBanker's SpecialCommando SpecialSpecificationsMass21 oz.Length6​ 3⁄ 4 inlength2 in3 inFeed systemSix-SightsFixedThe Colt Detective Special is a six-shot, framed, 2' barreled, and the first example of a class of firearms known to gun enthusiasts as. Made by this model revolver, as the name 'Detective Special' suggests, was intended to be concealed weapon used by plainclothes police.Introduced in 1927, the Detective Special was the first short-barreled revolver produced with a modern swing-out frame. It was designed from the outset to be chambered for higher-powered cartridges such as the, considered to be a powerful caliber for a concealable pocket revolver of the day. The Detective Special uses a slightly smaller frame than the or revolvers, but is larger than the five-shot // (J-frame) revolvers.Although the Detective Special proved to be an instant success when first introduced, lackluster sales saw the elimination of the Detective Special from the product line in 1995.

Fitz SpecialJohn Henry Fitzgerald an employee of Colt Firearms from 1918 to 1944, first came up the snubnosed revolver concept around the mid 1920s, when he modified a revolver, by shortening the barrel to two inches, shortening the ejector rod, bobbing the, rounding the butt, and removing the front half of the trigger guard. Reshaping the hammer and the butt allows the gun to be drawn quickly with little risk of the weapon snagging on clothing. The halved trigger guard facilitates quick trigger acquisition, even for shooters with large fingers or gloves.Although historians disagree, it's believe that somewhere between 40 to 200 Fitz Specials left the Colt factory, made from various Colt revolvers, by Fitzgerald himself. The Fitz Special was the precursor to the modern and specifically the prototype for the Colt Detective Special the first production two-inch snubnosed revolver. Even after the introduction of the Detective Special in 1927, Fitz continued to make custom revolvers for special clientele.The Detective Special.

A Colt Detective Special, Second Series on displayColt was so impressed with the Fitz Special that they decided to produce a sightly less radical version, the Detective Special, which is simply a shortened and somewhat streamlined. The Detective Special proved to be an instant success and was made until 1995.Colt's Detective Special went through several issues or series. The First Series was produced from 1927 until 1946. Compared to later production models, the First Series used a narrower frame, with reduced clearance between the frontstrap of the gripframe and the rear of the trigger guard.

Other distinctive features included a shorter ejector-rod with an ungrooved, knurled tip; a checkered hammer spur and cylinder latch, a 'half-moon'–shaped front sight, and an overlapping screw and locking pin set-up on the right side of the frame. Grip panels were wooden.

A rounded butt on the metal frame became standard in 1933, but pieces with the original square butt (like that of the Police Positive Special) continued to be produced into the 1940s.The Second Series ran from 1947 to 1972. The ejector-rod was longer and had a groove in its knurled tip; a three-inch-barrel variant was offered, with a yet longer ejector-rod. The cylinder latch was smooth, and the trigger spur serrated. The right side frame screw has no locking pin, and the rear half of the front sight is a serrated ramp. The grip panels were plastic in 1947, but were changed back to wood starting in 1955 (first with a silver-tone Colt medallion, and later a gold-tone). An optional hammer shroud was available from the factory to prevent the hammer from catching on clothing.Transition from the First to Second Series was gradual, with some post-WWII Second Series guns retaining short ejector rods and checkered hammers.

Because of this, assigning a given revolver to a particular issue is best done by serial number.During the 1960s, the grip frame of the Second Series Detective Special was shortened, matching that of Colt's other snub-nosed pistols, the. Despite this alteration, the Detective Special's overall grip size remained unchanged, as Colt fitted the Second Series with new, lengthened gripstocks that extended below the frame.The Third Series ran from 1973 to 1986. A new shroud extended down from the barrel, enclosing and protecting the ejector-rod, and the front sight was changed to a full ramp.

New, oversize wood gripstocks were introduced that covered the front frame strap. The Third Series featured improvements to the revolver's internal lockwork as well. As with the previous two Series, a few nickel-plated guns were produced, and a 3-inch-barrel variant was again offered. In 1986, facing stagnant sales numbers as well as rising production and labor costs, Colt discontinued production of the Detective Special. Colt stainless-steel SF-VIColt filed for bankruptcy protection in 1992.

After reorganization, the company restarted production of the Detective Special in 1993. The post-1992 Detective Special is sometimes called the Fourth Series, and featured 'composite' (rubber), wrap-around grips with a gold medallion. Only a two-inch barrel was offered, in blue or hard chrome finish. The new production run continued only until 1995, when Colt introduced its stainless-steel SF-VI as a replacement for the Detective Special.From its introduction, the Detective Special used Colt's ‘Positive Safety Lock’ , first featured on the Police Positive; the mechanism interposes a bar between hammer and frame until the trigger is pulled, preventing if the hammer is struck (e.g., if a dropped gun falls onto its hammer) with the trigger forward. First and early Second Series Detective Specials are becoming highly sought after by collectors, particularly if they are in prime condition and still have the famous Colt 'Royal Blue' finish.Calibers and finishes The Detective Special was initially available in both bright and finishes; a stainless steel finish replaced the nickeled option during the Fourth Series. For the Second Series, caliber options were.32 New Police,.38 New Police, and.38 Special; only.38 Special was offered for the other Series. The standard barrel length was 2 inches, but also a (rare) three-inch-barrel was offered during the Second and Third Series.

Submodels and variants One early variant based on the DS frame was the Colt Banker's Special. First produced in 1928, it was chambered in.38 Colt New Police (.38 S&W) and.22 Long Rifle. Few were made, particularly in.22LR caliber. The Banker's Special was popular with railway clerks, who often carried them on mail and parcel freight trains prior to World War II. During World War II production was discontinued, and the type was not revived following the war's end.The Colt Commando Special was a version of the Detective Special with a matte finish and rubber grips; produced from 1984 to 1986, it was chambered in.38 Special and weighed 21.5 oz.During the Fourth Series production run of 1993–1995, Colt offered the Detective Special with an optional de-spurred 'bobbed' hammer and lockwork, direct from the factory. The DAO or 'Bobbed Hammer' Detective Special was otherwise the same as the standard Fourth Series Detective Special.

Ammunition Interest has arisen over the use of higher-pressure (+P).38 Special ammunition in the Detective Special. In their more recent owners manuals, Colt authorized limited use of +P ammunition in steel-framed revolvers (including earlier versions), citing 2000 to 3000 rounds before recommending the gun be returned to the factory for inspection.

Many believe that this was due to potential liability rather than engineering requirements, as the standard pressure ammunition of yesteryear was about the same pressure as modern +P ammunition. Lowered the pressures in 1972. Usage Due to the good concealment qualities of the revolver, the Colt Detective Special was used as a weapon mostly by plainclothes police detectives, though it was also a popular off duty and backup firearm for uniformed police officers.

It was used by bodyguards, and for personal defense and shooting sports.The Colt Detective Special was a popular weapon before the semi-automatic pistol replaced the revolver in many police departments as well as law enforcement units and armies. And some other countries are still using the batches as officers' sidearms.Replacement Designated as the '9.65mm handgun', the Detective Special was used by the officers of the along with the designated as the '11.4mm handgun', only to be replaced by the semi-automatic pistol, the Japanese license-made. And a small number were used in some including the.The six-shot Colt Detective Special was the standard issue sidearm of Crime Wing inside, only to be replaced by after multiple years of use.The Colt Detective Special was the first revolver issued to French customs agents, meant to replace the old Browning 10/22 and MAB D pistols. They were used from 1975 to 1988, being progressively replaced by Smith & Wesson revolvers (mostly the S&W model 13) along with French Manurhins and the Sig Sauer SP 2022 in 2005.See also.References.

^ (15 March 2010). 'The Colt Detective Special'. Iola, wisconsin: Gun Digest Books. Pp. 55–63. Gun Review: Colt Detective Special revolver in.38 Spl.

Wood Grips For Colt Detective Special

The Fitz Special by Gary Paul Johnston, April 20, 2012. The Fitz Colt: The snub-nosed revolver benchmark 9/02/15 by Chris Eger.

Wood Grips For Colt Detective Special

Gun Review: Colt Detective Special revolver in.38 Spl. Fjestad, SP: Blue Book of Gun Values, 29th Edition; Blue Book Publications, Inc., Minneapolis, 2008. Trzoniec, Stanley W. 'Colt's Detective Special'. 21 (2). ^ January 12, 2008, at the. Colt Detective Special Owners Manual.

Hartford, Connecticut: Colt's Manufacturing. 15 January 2009.

Custom Grips For Colt Detective Special

Retrieved 21 April 2018. Sugiura, Hisaya (September 2015). 'Pistols of the Japanese police in the postwar era'.: 72–79.External links.

listing for. (.pdf).